Registers

Enable RADIO in TX mode

Enable RADIO in RX mode

Start RADIO

Stop RADIO

Disable RADIO

Start the RSSI and take one single sample of the receive signal strength

Stop the RSSI measurement

Start the bit counter

Stop the bit counter

Start the energy detect measurement used in IEEE 802.15.4 mode

Stop the energy detect measurement

Start the clear channel assessment used in IEEE 802.15.4 mode

Stop the clear channel assessment

Subscribe configuration for task TXEN

Subscribe configuration for task RXEN

Subscribe configuration for task START

Subscribe configuration for task STOP

Subscribe configuration for task DISABLE

Subscribe configuration for task RSSISTART

Subscribe configuration for task RSSISTOP

Subscribe configuration for task BCSTART

Subscribe configuration for task BCSTOP

Subscribe configuration for task EDSTART

Subscribe configuration for task EDSTOP

Subscribe configuration for task CCASTART

Subscribe configuration for task CCASTOP

RADIO has ramped up and is ready to be started

Address sent or received

Packet payload sent or received

Packet sent or received

RADIO has been disabled

A device address match occurred on the last received packet

No device address match occurred on the last received packet

Sampling of receive signal strength complete

Bit counter reached bit count value

Packet received with CRC ok

Packet received with CRC error

IEEE 802.15.4 length field received

Sampling of energy detection complete. A new ED sample is ready for readout from the RADIO.EDSAMPLE register.

The sampling of energy detection has stopped

Wireless medium in idle - clear to send

Wireless medium busy - do not send

The CCA has stopped

Ble_LR CI field received, receive mode is changed from Ble_LR125Kbit to Ble_LR500Kbit.

RADIO has ramped up and is ready to be started TX path

RADIO has ramped up and is ready to be started RX path

MAC header match found

Preamble indicator

Generated when last bit is sent on air, or received from air

CTE is present (early warning right after receiving CTEInfo byte)

Publish configuration for event READY

Publish configuration for event ADDRESS

Publish configuration for event PAYLOAD

Publish configuration for event END

Publish configuration for event DISABLED

Publish configuration for event DEVMATCH

Publish configuration for event DEVMISS

Publish configuration for event RSSIEND

Publish configuration for event BCMATCH

Publish configuration for event CRCOK

Publish configuration for event CRCERROR

Publish configuration for event FRAMESTART

Publish configuration for event EDEND

Publish configuration for event EDSTOPPED

Publish configuration for event CCAIDLE

Publish configuration for event CCABUSY

Publish configuration for event CCASTOPPED

Publish configuration for event RATEBOOST

Publish configuration for event TXREADY

Publish configuration for event RXREADY

Publish configuration for event MHRMATCH

Publish configuration for event SYNC

Publish configuration for event PHYEND

Publish configuration for event CTEPRESENT

Shortcuts between local events and tasks

Enable interrupt

Disable interrupt

CRC status

Received address

CRC field of previously received packet

Device address match index

Payload status

CTEInfo parsed from received packet

DFE status information

Packet pointer

Frequency

Output power

Data rate and modulation

Packet configuration register 0

Packet configuration register 1

Base address 0

Base address 1

Prefixes bytes for logical addresses 0-3

Prefixes bytes for logical addresses 4-7

Transmit address select

Receive address select

CRC configuration

CRC polynomial

CRC initial value

Interframe spacing in µs

RSSI sample

Current radio state

Data whitening initial value

Bit counter compare

Device address base segment n

Device address prefix n

Device address match configuration

Search pattern configuration

Pattern mask

Radio mode configuration register 0

IEEE 802.15.4 start of frame delimiter

IEEE 802.15.4 energy detect loop count

IEEE 802.15.4 energy detect level

IEEE 802.15.4 clear channel assessment control

Whether to use Angle-of-Arrival (AOA) or Angle-of-Departure (AOD)

Configuration for CTE inline mode

Various configuration for Direction finding

Start offset for Direction finding

GPIO patterns to be used for each antenna

Clear the GPIO pattern array for antenna control

Pin select for DFE pin n

Data pointer

Maximum number of buffer words to transfer

Number of samples transferred in the last transaction

Peripheral power control