WDT — Watchdog timer

The countdown watchdog timer (WDT) uses the low-frequency clock source (LFCLK) and offers configurable and robust protection against application lock-up.

WDT must be configured before it is started. After configuration, WDT is started by triggering the START task.

When WDT is running, its configuration registers (CRV, RREN, and CONFIG) are blocked for further configuration.

WDT can be paused while the CPU is sleeping, or when the debugger has halted the CPU. WDT is implemented as a down-counter that generates a TIMEOUT event when it wraps over after counting down to 0. When WDT is started by the START task, the watchdog counter is loaded with the value specified in the CRV register. This counter is also reloaded with the value specified in the CRV register when a reload request is granted.

The timeout period for the watchdog is given by the following equation:


      timeout [s] = ( CRV + 1 ) / 32768

When started, WDT will make the 32.768 kHz RC oscillator start if no other 32.768 kHz clock source is running and generating the 32.768 kHz system clock, see chapter CLOCK — Clock control.

Reload criteria

WDT has eight separate reload request registers. These registers are used to request WDT to reload its counter with the value specified in the CRV register. To reload the watchdog counter, write 0x6E524635 to all enabled reload registers.

One or more RR registers can be individually enabled through the RREN register.

Temporarily pausing the watchdog

By default, the watchdog will be active counting down the down-counter while the CPU is sleeping. It is possible to configure the watchdog to automatically pause when the CPU is sleeping or when it is stopped by the debugger.

Entering System OFF mode will stop and disable the watchdog.

Watchdog reset

A TIMEOUT event automatically leads to a watchdog reset.

If the watchdog is configured to generate an interrupt on the TIMEOUT event, the watchdog reset is postponed by two 32.768 kHz clock cycles after the TIMEOUT event is generated. Once the TIMEOUT event is generated, and unless the watchdog is stopped, the impending watchdog reset will occur.

The watchdog can be reset from several reset sources, see Application core reset behavior. After a reset, the watchdog configuration registers are available for configuration.

See RESET — Reset control for more information about reset sources.

Stopping the watchdog

By default, the watchdog cannot be stopped. It is possible to configure the watchdog to allow the STOP task.

To stop the watchdog, perform the following steps.

Set the CONFIG register's STOPEN field to Enable during watchdog configuration.
Write the special value 0x6E524635 to the TSEN register.
Invoke the STOP task.

When these conditions are met, the watchdog is stopped and a STOPPED event is issued.

When the watchdog is stopped, its configuration registers CRV, RREN, and CONFIG are no longer blocked.

Note: It is recommended to write zeros to TSEN after the watchdog has stopped, to avoid runaway code triggering the STOP task.

Registers

Instances


Instance	Domain	Base address	TrustZone			Split access	Description
Instance	Domain	Base address	Map	Att	DMA	Split access	Description
WDT0 : S WDT0 : NS	APPLICATION	0x50018000 0x40018000	US	S	NA	No	Watchdog timer 0
WDT1 : S WDT1 : NS	APPLICATION	0x50019000 0x40019000	US	S	NA	No	Watchdog timer 1
WDT	NETWORK	0x4100B000	HF	NS	NA	No	Watchdog timer

Register overview


Register	Offset	Description
TASKS_START	0x000	Start WDT
TASKS_STOP	0x004	Stop WDT
SUBSCRIBE_START	0x080	Subscribe configuration for task START
SUBSCRIBE_STOP	0x084	Subscribe configuration for task STOP
EVENTS_TIMEOUT	0x100	Watchdog timeout
EVENTS_STOPPED	0x104	Watchdog stopped
PUBLISH_TIMEOUT	0x180	Publish configuration for event TIMEOUT
PUBLISH_STOPPED	0x184	Publish configuration for event STOPPED
INTENSET	0x304	Enable interrupt
INTENCLR	0x308	Disable interrupt
NMIENSET	0x324	Enable interrupt
NMIENCLR	0x328	Disable interrupt
RUNSTATUS	0x400	Run status
REQSTATUS	0x404	Request status
CRV	0x504	Counter reload value
RREN	0x508	Enable register for reload request registers
CONFIG	0x50C	Configuration register
TSEN	0x520	Task stop enable
RR[n]	0x600	Reload request n

TASKS_START

Address offset: 0x000

Start WDT


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	W	TASKS_START										Start WDT
			Trigger	1								Trigger task

TASKS_STOP

Address offset: 0x004

Stop WDT


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	W	TASKS_STOP										Stop WDT
			Trigger	1								Trigger task

SUBSCRIBE_START

Address offset: 0x080

Subscribe configuration for task START


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				B																								A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	CHIDX		[0..255]								DPPI channel that task START will subscribe to
B	RW	EN
			Disabled	0								Disable subscription
			Enabled	1								Enable subscription

SUBSCRIBE_STOP

Address offset: 0x084

Subscribe configuration for task STOP


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				B																								A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	CHIDX		[0..255]								DPPI channel that task STOP will subscribe to
B	RW	EN
			Disabled	0								Disable subscription
			Enabled	1								Enable subscription

EVENTS_TIMEOUT

Address offset: 0x100

Watchdog timeout


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	EVENTS_TIMEOUT										Watchdog timeout
			NotGenerated	0								Event not generated
			Generated	1								Event generated

EVENTS_STOPPED

Address offset: 0x104

Watchdog stopped


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	EVENTS_STOPPED										Watchdog stopped
			NotGenerated	0								Event not generated
			Generated	1								Event generated

PUBLISH_TIMEOUT

Address offset: 0x180

Publish configuration for event TIMEOUT


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				B																								A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	CHIDX		[0..255]								DPPI channel that event TIMEOUT will publish to
B	RW	EN
			Disabled	0								Disable publishing
			Enabled	1								Enable publishing

PUBLISH_STOPPED

Address offset: 0x184

Publish configuration for event STOPPED


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				B																								A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	CHIDX		[0..255]								DPPI channel that event STOPPED will publish to
B	RW	EN
			Disabled	0								Disable publishing
			Enabled	1								Enable publishing

INTENSET

Address offset: 0x304

Enable interrupt


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																		B	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	TIMEOUT										Write '1' to enable interrupt for event TIMEOUT
			Set	1								Enable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled
B	RW	STOPPED										Write '1' to enable interrupt for event STOPPED
			Set	1								Enable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled

INTENCLR

Address offset: 0x308

Disable interrupt


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																		B	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	TIMEOUT										Write '1' to disable interrupt for event TIMEOUT
			Clear	1								Disable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled
B	RW	STOPPED										Write '1' to disable interrupt for event STOPPED
			Clear	1								Disable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled

NMIENSET

Address offset: 0x324

Enable interrupt


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																		B	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	TIMEOUT										Write '1' to enable interrupt for event TIMEOUT
			Set	1								Enable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled
B	RW	STOPPED										Write '1' to enable interrupt for event STOPPED
			Set	1								Enable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled

NMIENCLR

Address offset: 0x328

Disable interrupt


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																		B	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	RW	TIMEOUT										Write '1' to disable interrupt for event TIMEOUT
			Clear	1								Disable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled
B	RW	STOPPED										Write '1' to disable interrupt for event STOPPED
			Clear	1								Disable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled

RUNSTATUS

Address offset: 0x400

Run status


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	R	RUNSTATUSWDT										Indicates whether or not WDT is running
			NotRunning	0								Watchdog is not running
			Running	1								Watchdog is running

REQSTATUS

Address offset: 0x404

Request status


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																												H	G	F	E	D	C	B	A
Reset 0x00000001				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	1
ID	R/W	Field	Value ID	Value								Description
A-H	R	RR[i] (i=0..7)										Request status for RR[i] register
			DisabledOrRequested	0								RR[i] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[i] register is enabled, and are not yet requesting reload

CRV

Address offset: 0x504

Counter reload value


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0xFFFFFFFF				1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1
ID	R/W	Field	Value ID	Value								Description
A	RW	CRV		[0xF..0xFFFFFFFF]								Counter reload value in number of cycles of the 32.768 kHz clock

RREN

Address offset: 0x508

Enable register for reload request registers


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																												H	G	F	E	D	C	B	A
Reset 0x00000001				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	1
ID	R/W	Field	Value ID	Value								Description
A-H	RW	RR[i] (i=0..7)										Enable or disable RR[i] register
			Disabled	0								Disable RR[i] register
			Enabled	1								Enable RR[i] register

CONFIG

Address offset: 0x50C

Configuration register


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID																													C			B			A
Reset 0x00000001				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	1
ID	R/W	Field	Value ID	Value								Description
A	RW	SLEEP										Configure WDT to either be paused, or kept running, while the CPU is sleeping
			Pause	0								Pause WDT while the CPU is sleeping
			Run	1								Keep WDT running while the CPU is sleeping
B	RW	HALT										Configure WDT to either be paused, or kept running, while the CPU is halted by the debugger
			Pause	0								Pause WDT while the CPU is halted by the debugger
			Run	1								Keep WDT running while the CPU is halted by the debugger
C	RW	STOPEN										Allow stopping WDT
			Disable	0								Do not allow stopping WDT
			Enable	1								Allow stopping WDT

TSEN

Address offset: 0x520

Task stop enable


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	W	TSEN										Allow stopping WDT
			Enable	0x6E524635								Value to allow stopping WDT

RR[n] (n=0..7)

Address offset: 0x600 + (n × 0x4)

Reload request n


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
ID	R/W	Field	Value ID	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

Electrical specification

Watchdog Timer Electrical Specification


Symbol	Description	Min.	Typ.	Max.	Units
t_WDT	Time out interval	..	..	..