nRF52832 Engineering A Errata

nRF52832 Engineering A Errata
Change log
New and inherited anomalies
[1] I2S: I2S not functional
[2] PWM: PWM not functional
[3] PDM: PDM not functional
[4] MWU: MWU not functional
[7] NVMC,System: Cache is not functional
[8] SAADC: Increased current consumption in system ON-IDLE
[9] QDEC: Some features are not functional
[10] RTC: RTC2 is not functional
[11] System: Device is unable to stay in System OFF mode
[12] COMP: Reference ladder is not correctly calibrated
[15] POWER: RAM[x].POWERSET/CLR read as zero
[16] System: RAM may be corrupt on wakeup from CPU IDLE
[17] NFCT: The EVENTS_FIELDLOST is not generated
[20] RTC: Register values are invalid
[23] SPIM: END event is generated before ENDTX
[24] NFCT: The FIELDPRESENT register read is not reliable
[25] NFCT: Reset value of SENSRES register is incorrect
[26] NFCT: NFC field does not wakeup the device from emulated system OFF
[27] NFCT: Triggering NFCT ACTIVATE task also activates the Rx easyDMA
[28] SAADC: Scan mode is not functional for some analog inputs
[29] TWIS: Incorrect bits in ERRORSRC
[30] TWIS: STOP Task is not functional
[31] CLOCK: Calibration values are not correctly loaded from FICR at reset
[32] DIF: Debug session automatically enables TracePort pins
[33] System: Code RAM is located at wrong address
[34] System: Code and Data RAM are not mapped from the same physical RAM
[35] CLOCK: HFCLK can draw current when not requested
[36] CLOCK: Some registers are not reset when expected
[37] RADIO: Encryption engine is slow by default.
[38] PPI: Enable/disable tasks for channel group 4 and 5 cannot be triggered through PPI
[39] NFCT: The automatic collision resolution does not handle CRC and parity errors
[40] NFCT: The FRAMEDELAYMODE = WindowGrid is not supported
[41] GPIO: PIN_CNF[x] registers not reset after pin reset
[42] PPI: FORK on the fixed channels is not functional
[43] SPIS: SPIS0 is not functional
[44] NVMC: Read after flash erase is unpredictable
[46] SPIM,TWIM: EasyDMA list not functional
[47] DIF: Trace is not functional
[48] DIF: SWO only works if Trace is enabled.
[49] RTC: RTC is not functional after LFCLK is restarted
[57] NFCT: NFC Modulation amplitude
[58] SPIM: An additional byte is clocked out when RXD.MAXCNT = 1
[63] POWER: DC/DC does not automatically switch off in System ON IDLE
[64] NFCT: Only full bytes can be received or transmitted, but supports 4-bit frame transmit
[65] POWER: RAM[] registers mapping of RAM block and sections is wrong
[67] NFCT,PPI: Some events cannot be used with the PPI
[68] CLOCK: EVENTS_HFCLKSTARTED can be generated before HFCLK is stable
[70] COMP: Not able to wake CPU from System ON IDLE
[71] CLOCK: RCOSC calibration
[72] NFCT,PPI: TASKS_ACTIVATE cannot be used with the PPI
[73] TIMER: Event lost
[74] SAADC: Started events fires prematurely
[77] CLOCK: RC oscillator is not calibrated when first started
[78] TIMER: High current consumption when using timer STOP task only
[84] COMP: ISOURCE not functional
[86] SAADC: Triggering START task after offset calibration may write a sample to RAM
[87] CPU: Unexpected wake from System ON Idle when using FPU
[88] WDT: Increased current consumption when configured to pause in System ON idle
[97] GPIOTE: High current consumption in System ON Idle mode

Back to home page